How to Build a Shed - Building Sheds, Playhouses and Outbuildings in the Garden
Summary: In this DIY guide our experts show you how to build a shed. Find out how to build sheds, a playhouse or outbuildings with step-by-step shed building advice and tips covering building a garden shed, felting a shed roof, alternatives to traditional felt shed roofs and fitting shed windows. Whether you're building a simple garden shed or a "Global Shed-quaters" the building principles are the same!
Sheds, playhouses and outbuildings are classified as temporary structures so you normally do not need to obtain planning permission for these structures, unless you live in a conservation area. They are relatively simple to construct and can be placed just about anywhere provided there is a firm and flat surface. Before we run through the steps on how to build a shed there are some issues to consider:
- How big do you want your shed – the size of your shed should compliment the size of your garden. Try not to overwhelm your garden. Think about the colour and aesthetics of the shed.
- The shed needs to be accessible with a pathway and a sensibly placed doorway.
- Placement of the shed is important, your shed should not be in an awkward position, rather place it where it is out of the way but still accessible, a good place is often against the back or side wall – perhaps the corner.
- Natural light is an issue in winter? Choose the correct side for the window/s to provide maximum light. Is there a danger of overheating in summer?
- Is the shed going to be powered? How will you get the power to the shed? Think underground cables.
- Do you need running water in your shed? Is there a tap nearby where you can source water?
- Try and make your shed versatile – a children’s playhouse can later be made into a workshop or storeroom when they grow up.
Building The Shed
A garden shed is fairly simple to build. There are obviously more elaborate options with extra windows and double doors, but most are standardised. Some sheds are even wired and heated. Proper heavy duty locks can be fitted for extra security.
- To begin with you will need to lay a base slab; the slab should be 25mm smaller than the floor of your shed, to ensure proper drainage, for the same reason the slab should also be slightly tilted to allow for drain off of any water. For more information on laying a shed base slab see our Building a Shed Base project .
- Once you have your slab in place you need to centre the shed floor on it. The centre points of the side panels and the floor should all be marked so that they will line up in the next step.
Step 2: Centre the floor on top of the concrete base
Step 3: Lift gable end into position and one of the side panels and then secure top, middle and bottom using 50mm countersunk screws
Step 5: Position and fix the front gable end onto the other panels, but do not secure to the floor yet
Step 6: Fit the roof support beam across the top of the shed between the front and rear gable ends
Step 9: Lay the roof panels on
the ground one at a time and fix
Step 10: Lift the roof panels into place one at a time and fix them in position along the top of the side panels and gable ends
Step 11: Using the internal diagonal measurements of a shed to get it square for fixing to shed base
Felting The Shed Roof
- You will need to cut the felt to size with a sharp blade (Stanley knife or similar). Cut three pieces, two of them should be slightly larger then the roof panels (+50mm) and one of the pieces should be cut to cover the gap at the apex and extend at least 75mm over each roof panel. Ensure that you measure each roof panel to get it's exact size.
Step 1: Cut felt into size with a sharp blade
Step 2: Lay the first piece of felt over one side panel
Step 5: Tidy up the felt at the corners and fix on the gable end facia boards
Rubber Roofing for Your Shed
Another consideration when roofing your new shed is how accessible it is – at some point you may need to replace the felt. A long lasting alternative could be rubber roofing. Available as one piece of membrane cut to size, there are no joins or overlaps to worry about.
If your felt roof leaks, it can be very difficult to firstly see where the problem is and even more difficult to patch. Rubber roofing may seem a little odd for a shed, but will alleviate all these worries.
DIY rubber roof kits are widely available today and the kit should include everything that you will need in order to cover your shed roof with a long lasting, EPDM rubber membrane (that also features a lifetime membrane guarantee), including the adhesive, trim and full installation instructions.
The membrane is glued to the shed roof using a totally safe, water based adhesive and due to the fact that it doesn't feature any joints that could fail and cause leaks, you can be sure that these issues will not arrise in the future.
A further benefit is that they should also be completely UV stable, so no degrading of the rubber over time.
Fitting The Shed Windows
Most shed windows nowadays are Perspex or acrylic, which are very easy to install and obviously cheaper and safer than glass. They slide easily into their housing in the window frame.
- You need to be outside to begin installing the windows. Firstly slide the metal window sill (should be provided with your shed kit) into the grooves provided at the bottom of the window frame.
Step 1: Slot metal window sill into position and fix
Step 2: Nail in the window cloaks
Step 3: From inside the shed, slide the perspex into place and secure it
You should now be well voiced in how to build a shed and the principles of this job can also be translated over to the construction of many other structures such as playhouses and outbuildings.
Why not take a look at our video section on building a shed to watch a film on shed building for a practical demonstration .
Don't fancy doing this project yourself? We work with Checkatrade to ensure that we recommend only reliable and trustworthy tradesmen.